1.准备工作
%A
%A 现在确认你有一支Conexant USB ADSL的Modem和以下文件，(如果您没有备齐这些东西，下面的工作将无法进行)
%A
%A 引用:
%A cxacru.tar.bz2 rp-pppoe-3.5.tar.gz Kernel-2.6.x patch-2.6.X_date_accessrunner.gz
%A
%A
%A 说明：
%A
%A 其中cxacru.tar.bz2(要在此处下载我已经打好补丁的文件)是USB ADSL的驱动程序文件源代码包
%A
%A rp-pppoe-3.5.tar.gz(或更高版本)是pppoe的拨号程序源代码包
%A
%A Kernel-2.6.x是Kernel的源代码包
%A
%A patch-2.6.X_date_accessrunner.gz是内核的补丁文件
%A
%A 确定备齐以上文件后就可以进行下面的工作了
%A
%A 2.开始安装
%A
%A 首先将设备联结好
%A
%A 2.1给内核打补丁并编译内核
%A
%A 解压内核包把patch-2.6.X_date_accessrunner.gz拷贝到内核目录的上级目录
%A
%A 执行 代码:
%A gunzip -c patch-2.6.x_YYYYMMDD_accessrunner.gz | patch -p1
%A
%A
%A 如果你的Kernel已经有如下支持(可以在Kernel的.config文件中查找到)就不必重新编译
%A 代码:
%A
%A Code maturity level options
%A
%A [*] Prompt for development and/or incomplete code/drivers
%A
%A Loadable module support
%A
%A [*] Enable loadable module support
%A
%A [*] Set version information on all module symbols
%A
%A [*] Kernel module loader
%A
%A Networking options
%A
%A <*> Packet socket
%A
%A <*> Unix domain sockets
%A
%A [*] TCP/IP networking
%A
%A [*] Asynchronous Transfer Mode (ATM)
%A
%A USB support
%A
%A <*> Support for USB
%A
%A [*] Preliminary USB device filesystem
%A
%A UHCI
%A
%A OHCI
%A
%A Alcatel Speedtouch USB support (USB_SPEEDTOUCH)
%A     
%A Networking options
%A
%A [*] Asynchronous Transfer Mode (ATM)
%A
%A [*] Classical IP over ATM
%A
%A
%A Networking options
%A
%A [M] RFC1483/2684 Bridged protocols
%A
%A Network Device Support
%A
%A PPP (point-to-point protocol) support
%A
%A PPP Deflate compression
%A
%A PPP over Ethernet (EXPERIMENTAL)
%A
%A
%A Network Device Support
%A
%A PPP (point-to-point protocol) support
%A
%A PPP Deflate compression
%A
%A PPP over ATM
%A
%A   Processor type and features
%A
%A [ ] Symmetric multi-processing support
%A
%A Cryptographic API (CRYPTO)
%A
%A CRC32c CRC algorithm (CRYPTO_CRC32C)
%A
%A Library routines
%A
%A CRC32c (Castagnoli, et al) Cyclic Redundancy-Check (LIBCRC32C)
%A
%A
%A 设置好后 make 、make modules 、make modules_install、make install、reboot
%A
%A 2.2编译驱动和拨号程序
%A
%A 解压cxacru.tar.bz2，ln /内核源代码目录 /usr/linux -s
%A
%A 然后在源代码目录中make，
%A
%A 解压rp-pppoe-3.5.tar.gz，在其目录中执行./go 如果你用X 就可以用./go-gui
%A
%A 设置好你的拨号程序，要注意的是在填写设备的时候要填写nas0
%A
%A nas0是驱动程序虚拟出来的USB Modem
%A
%A 2.3设置协议
%A
%A 编辑/etc/cxacru文件，像这个样子：
%A 代码:
%A
%A #
%A # Config file for Conexant AccessRunner
%A #
%A
%A # Driver mode
%A DRIVER_MODE=1  # 1 = normal, 2 = debug, 3 = normal+max speed (without ask adsl status), 4 = debug+max speed (without ask adsl status)
%A
%A # Protocol
%A PROTOCOL_MODE=4  # 1 = RFC1483/2684 routed, 2 = PPP over ATM (pppoa), 3 = RFC1483/2684 bridged, 4 = PPP over Ethernet (pppoe)
%A
%A # Paths
%A BINARY_PATH="/usr/sbin"
%A ATM_PATH=""
%A
%A # ADSL
%A #  if OPEN_MODE is blank then cxload uses default mode acoording VID & PID
%A #  Values for OPEN_MODE are:
%A #    0 = auto selection, G.Handshake
%A #    1 = auto selection, T1.413
%A #    2 = G.Handshake
%A #    3 = ANSI T1.413
%A #    4 = ITU-T G.992.1 (G.DMT)
%A #    5 = ITU-T G.992.2 (G.LITE)
%A OPEN_MODE=4
%A
%A # ATM
%A VPI=0
%A VCI=33
%A
%A # Specific for RFC1483/2684 routed/bridged
%A #  if IP_ADDRESS is blank in bridged mode then it uses DHCP to get IP
%A IP_ADDRESS=
%A NETMASK=255.255.255.255
%A GATEWAY=
%A
%A
%A 需要更改的是# Protocol # ADSL # ATM
%A
%A 如果你用的是RFC1483/2684协议还要设置# Specific for RFC1483/2684 routed/bridged
%A
%A PPPOE和PPPOA的用户只要修改# Protocol # ADSL # ATM 这3项就可以了
%A
%A 3.拨号
%A
%A 在终端下输入cxstart.sh建立连接 cxstop.sh断掉连接
%A
%A 用ifconfig检查一下你是否已经连上了，像这个样子：
%A 代码:
%A
%A [root@Love root]# ifconfig
%A lo        Link encap:Local Loopback
%A           inet addr:127.0.0.1  Mask:255.0.0.0
%A           inet6 addr: ::1/128 Scope:Host
%A           UP LOOPBACK RUNNING  MTU:16436  Metric:1
%A           RX packets:0 errors:0 dropped:0 overruns:0 frame:0
%A           TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
%A           collisions:0 txqueuelen:0
%A           RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
%A
%A nas0      Link encap:Ethernet  HWaddr 00:00:01:00:00:00
%A           inet6 addr: fe80::200:1ff:fe00:0/64 Scope:Link
%A           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
%A           RX packets:17650 errors:0 dropped:0 overruns:0 frame:0
%A           TX packets:15790 errors:0 dropped:0 overruns:0 carrier:0
%A           collisions:0 txqueuelen:1000
%A           RX bytes:15856545 (15.1 Mb)  TX bytes:2128934 (2.0 Mb)
%A
%A ppp0      Link encap:Point-to-Point Protocol
%A           inet addr:221.214.196.80  P-t-P:221.0.64.38  Mask:255.255.255.255
%A           UP POINTOPOINT RUNNING NOARP MULTICAST  MTU:1492  Metric:1
%A           RX packets:16454 errors:0 dropped:0 overruns:0 frame:0
%A           TX packets:14588 errors:0 dropped:0 overruns:0 carrier:0
%A           collisions:0 txqueuelen:3
%A           RX bytes:15674609 (14.9 Mb)  TX bytes:1613794 (1.5 Mb)
%A
%A [root@Love root]#
%A
%A
%A 如果有nas0和ppp0那么恭喜你你已经成功了！  
%A   
%A